Mustang 2066 2076 2086 Including 2076 (EU) 2086 (EU) Skid-Steer Loader Operator’s Manual 917326-DP0112 – PDF DOWNLOAD
FILE DETAILS:
Mustang 2066 2076 2086 Including 2076 (EU) 2086 (EU) Skid-Steer Loader Operator’s Manual 917326-DP0112 – PDF DOWNLOAD
Language : English
Pages : 108
Downloadable : Yes
File Type : PDF
Size: 3.11 MB
DESCRIPTION:
Mustang 2066 2076 2086 Including 2076 (EU) 2086 (EU) Skid-Steer Loader Operator’s Manual 917326-DP0112 – PDF DOWNLOAD
INTRODUCTION :
This Operator’s Manual gives the owner/operator information about maintaining and servicing 2066, 2076 and 2086, including 2076 (EU) and 2086 (EU), skidsteer loader models. More important, this manual provides an operating plan for safe and proper use of the machine. Major points of safe operation are detailed in the Safety chapter of this manual.
- We ask that users read and understand the contents of this manual completely and become familiar the new machine before operating it. Contact your authorized Mustang dealer if you have any questions regarding information in this manual, need extra manuals, or for information concerning the availability of manuals in other languages.
- Throughout this manual information is provided set in italic type and introduced by the word, Notice, Note or Important. Read carefully and comply with those messages – it will improve operating and maintenance efficiency, help avoid breakdowns and damage, and extend the machine’s life.
- A manual storage box in the operator’s compartment holds the Operator’s Manual and AEM Safety Manual (also available in Spanish). Please return the manuals to this box and keep them with the unit at all times. If this machine is resold, Mustang recommends that these manuals be given to the new owner.
- The attachments and equipment available for use with this machine have a wide variety of potential applications. Read the manual provided with the attachment to learn how to safely maintain and operate the equipment. Be sure the machine is suitably equipped for the type of work to be performed.
- Do not use this machine for any applications or purposes other than those described in this manual or applicable for approved attachments. If the machine is to be used with special attachments or equipment other than those approved by Manitou Americas, consult your Mustang dealer.
- Any person using nonapproved attachments or making unauthorized modifications is responsible for the consequences. The Mustang dealership network stands ready to provide any assistance that may be necessary, including providing genuine Mustang service parts. All service parts should be obtained from your Mustang dealer.
- Provide complete information about the part and include the model and serial numbers of the machine. Record these numbers in the space provided on the Table of Contents page, as a handy reference. Please be aware that Manitou Americas strives to continuously improve its products and reserves the right to make changes and improvements in the design and construction of any part without incurring the obligation to install such changes on any unit previously delivered.
- If this machine was purchased “used,” or if the owner’s address has changed, please provide your Mustang dealer or Mustang Service Department with the owner’s name and current address, along with the machine model and serial 2 number. This will allow the registered owner information to be updated, so that the owner can be notified directly in case of an important product issue, such as a safety update program.
TABLE OF CONTENTS:
Mustang 2066 2076 2086 Including 2076 (EU) 2086 (EU) Skid-Steer Loader Operator’s Manual 917326-DP0112 – PDF DOWNLOAD
2066, 2076 and 2086 Skid-Steer Loaders Operator’s Manual 3
Introduction 5
Loader Identification 7
1 Lift Arm 7
2 Front Work Lights 7
3 Restraint Bar 7
4 Handholds 7
5 Tilt Cylinders 7
6 Attachment Bracket 7
7 Tires 7
1 Engine Cover 7
2 Rear Work Lights 7
3 Tail Lights 7
4 Rear Door 7
5 Counterweight (optional) 7
6 Lift Cylinder 7
7 Roll-Over/Falling Object Protective System (ROPS/FOPS) 7
Control/Indicator Symbols 8
Power Off 8
Power On 8
Engine Start 8
Battery Charge 8
Electrical Power 8
Worklight w/Tail Lights 8
Worklight 8
Safety Alert 8
Hazard Flasher 8
Fasten Seatbelt 8
Horn 8
Read Operator’s Manual 8
Volume – Full 8
Volume – Half Full 8
Volume – Empty 8
H-L 8
High – Low 8
N 8
Neutral 8
F 8
Forward 8
R 8
Reverse 8
Parking Brake 8
Engine Air Filter 8
Engine Oil 8
Engine Oil Filter 8
Engine Oil Pressure 8
Fuel Filter 8
Engine Temperature 8
Hydraulic System 8
Hydraulic Oil Temperature 8
Hydraulic Oil Filter 8
Grease Lubrication Point 8
Glow Indicator Lamp 8
Diesel Fuel 8
Chaincase Oil 8
Clockwise Rotation 8
Counterclockwise Rotation 8
Fast 8
Slow 8
Ride Control 8
Engine Malfunction Shutdown 8
Bucket – Float 8
Bucket – Rollback 8
Bucket – Dump 8
Lift Arm – Lower 8
Lift Arm – Raise 8
Service Hours 8
Lift Point 8
Tie-Down 8
Diesel Water Separator 8
Power-A-Tach® 8
Safety 9
Mandatory Safety Shutdown Procedure 10
1 Move the drive control handle(s) to the neutral position 10
2 Lower the lift arm and attachment completely If the lift arm must be left in the raised position, be sure to properly engage the lift arm support device (page 22) 10
3 Move the throttle to the low idle position, shut off the engine and remove the key 10
4 Before exiting, move the lift/tilt control(s) to verify that the controls do not cause movement of the lift arm and hitch 10
Safety Reminders 10
Potential Hazards 12
Safety Decals 12
New Decal Application 12
ANSI-Style Safety Decals inside the ROPS/FOPS 13
ANSI-Style Safety Decals on the outside of the Loader 14
ANSI-Style Safety Decals on the outside of the Loader 15
ANSI-Style Safety Decals in the Engine Compartment 16
ISO-Style (used Internationally) Safety Decals inside the ROPS/FOPS 17
ISO-Style (used Internationally) Safety Decals on the outside of the Loader 18
ISO-Style (used Internationally) Safety Decals on the outside of the Loader 19
ISO-Style (used Internationally) Safety Decals in the Engine Compartment 20
Product and Component Plate Locations 21
Controls and Safety Equipment 23
Guards and Shields 23
Operator Restraint Bar 23
Operator’s Seat 24
Figure 1 Operator’s Seat 24
1 Restraint Bar 24
2 Seatbelt 24
3 Seat Position Adjustment Lever 24
4 Suspension Seat Weight Adjustment Knob (optional) 24
Upper-Torso Restraint 24
Safety Interlock System 24
Hydraloc™ 24
Testing the Safety Interlock System 25
ROPS/FOPS 25
Parking Brake 25
Figure 2 Parking Brake Switch 25
Horn 26
Rear Window Emergency Exit 26
Lift Arm Support Device 26
Engagement 26
Figure 3 Lift Arm Support Device Engaged 26
1 Lower the lift arm fully 26
2 Stop the engine 26
3 Leave the operator’s compartment Remove the lock pin holding the support device against the lift arm Allow the support device to lower into contact with the lift cylinder 26
4 Return to operator’s compartment and restart the engine 26
5 Use the lift control to raise the lift arm until the support device drops over the end of the lift cylinder and around the cylinder rod Slowly lower the lift arm until the freed of the support device contacts the top of the lift cylinder 26
6 Look to make sure the support device is secure against the cylinder end Then, stop the loader engine, remove the key and leave the operator’s compartment 26
Disengagement 27
1 Start the engine; 27
2 Raise the lift arm fully; 27
3 Stop the engine; 27
4 Before leaving the operator’s compartment, check to make sure that the lift arm is being held in the raised position (See Notice below) 27
Figure 4 Lift Arm Support Device Storage Location 27
5 To store the support device, raise it and move it forward until the storage peg protrudes through the support Insert the lock pin underneath the support through the hole in the support peg 27
Accessory Plug 27
Dome Light 27
Work Lights 27
Heater (optional) 27
Heater and Air Conditioner (optional) 28
Figure 5 Heater/ Air Conditioner Controls 28
1 Fan Speed: Controls the air flow 28
2 Heater/Air Conditioner Selector Switch: Turns on either the heater or the air conditioner 28
Engine Speed Control 28
Figure 6 Hand Throttle 28
Figure 7 Foot Throttle (Joystick control units) 28
Two-Speed Drive (optional) 29
Hydraglide™ Ride Control System 29
Attachment Mounting 29
Multi-Tach™ Hitch 29
Figure 8 Multi-Tach™ Hitch 29
Power-A-Tach® Hitch 30
Figure 9 Power-A-Tach® Hitch 30
Instrument Panels 31
Figure 10 Left Panel 31
Left Panel 31
1 Two-Speed Transmission (optional) – Lights when high speed is engaged 31
2 Parking Brake – Lights when the parking brake is applied 31
3 Power-A-Tach® – Used to actuate the Power-A-Tach 31
4 Fan (optional) – Used to control the fan speed for the air conditioner and heater 31
5 Heater/Air Conditioner Selector (optinal) – Used to control the heater and air conditioner 31
6 Accessory Plug – 12-volt DC power outlet 31
7 Engine Malfunction – Lights when the engine electronic control unit (ECU) has detected a failure warranting an automatic shutdown The indicator lamp also displays error codes when the key switch is turned to the “on” position See Engine Di 31
8 Hydraglide™ Ride Control System – Lights when the ride control system is activated 31
9 Float Indicator Switch – Lights when float function is activated 31
10 Parking Brake Switch – Used to manually apply the parking brake 31
Right Panel 32
Figure 11 Right Panel 32
1 Hourmeter – Displays the total operating hours of the loader 32
2 Fuel Level Gauge – Displays the amount of fuel in the tank 32
3 Engine Coolant Temperature Gauge – Displays the temperature of the engine coolant 32
4 Engine Coolant Temperature – Lights if the engine coolant is too hot This warns the operator to stop the engine and determine and correct the cause of the high temperature During normal operation this indicator should be OFF 32
5 Hydraulic Oil Temperature – Lights if the hydraulic oil is too hot This warns the operator to reduce the hydraulic load and determine the cause of the high temperature During normal operation this indicator should be OFF 32
6 Light Switch – Controls all the lights on the loader Symbols denote the four positions of the light switch In a clockwise direction these are: 32
7 High-Flow Auxiliary Switch (optional) – Controls the direction of hydraulic oil flow Push the right side of the rocker switch for forward flow, or the left side for reverse flow To disengage, push and release either side of the switch or raise 32
8 Keyswitch – In a clockwise rotation, these positions are: 33
9 Engine Speed Control – Controls the engine speed Move the control clockwise to increase and counter-clockwise to decrease the engine speed 33
10 Fasten Seatbelt – A momentary visual (and audible) indicator to remind the operator to fasten the seatbelt(s) 33
11 Battery – Lights if the charging voltage is too high or too low During normal operation this indicator should be OFF 33
12 Preheat Indicator Lamp – Lights when the (automatic) preheat is active During normal operation this indicator should be OFF 33
13 Engine Oil Pressure – Lights if the engine oil pressure is too low Warns the operator to immediately stop the engine and determine the cause for the low pressure During normal operation this indicator should be OFF 33
14 Engine Air Restriction Indicator (optional) – Lights when a restriction in the engine air filter is detected Warns the operator to immediately stop the engine and clean or replace the element in the engine air cleaner During normal operation th 33
15 Hydraulic Oil Filter Indicator (optional) – Lights if the hydraulic oil filter becomes restricted Warns the operator to immediately stop the engine, allow the engine to cool, and then change the oil and filter During normal operation this indic 33
Joystick Controls 34
Figure 12 Joystick Controls 34
1 Lift/Tilt Control 34
2 Drive Control 34
Drive Controls 34
Lift/Tilt Control 35
Hand/Foot Controls 36
Figure 13 Hand/Foot Controls 36
1 Left Drive Control Handle 36
2 Right Drive Control Handle 36
3 Lift Control Pedal 36
4 Tilt Control Pedal 36
Drive Controls 36
Lift/Tilt Controls 37
Auxiliary Hydraulic Controls 38
Standard-Flow Auxiliary Hydraulic Control 38
Figure 14 Electric Auxiliary Control 38
High-Flow Auxiliary Hydraulic Control (optional) 39
Figure 15 High-Flow Auxiliary Switch 39
Notes 40
Operation 41
Before Starting the Engine 41
Fuel 41
Starting the Engine 41
1 Carefully step up onto the back of the bucket or attachment and grasp the handholds to enter the operator’s compartment 41
2 Fasten the seatbelt(s) and lower the restraint bar 41
3 Verify the following: 41
4 Turn the key to the START position 41
Cold-Starting 42
Cold-Starting Procedure 42
1 Turn the key to the RUN position If the preheat light on the right instrument panel comes on, wait until it goes out 42
2 Turn the key to the START position 42
3 If engine does not start, return key to OFF position and repeat steps 1 and 2 42
Stopping the Loader 42
1 Check that the drive control handle(s) is (are) in neutral position; 42
2 Lower the lift arm and rest the attachment on the ground; 42
3 Turn throttle knob back to the low idle position (and release the throttle pedal for joystick control machines); 42
4 Turn the keyswitch to the OFF position and remove the key; and 42
5 Raise the restraint bar, unfasten the seatbelt(s) and grasp the handholds while climbing out of the operator’s compartment 42
Parking the Loader 43
Jump-starting 43
1 Turn the keyswitches of both vehicles to OFF Be sure the vehicles are in “neutral” and NOT touching each other 43
2 Connect the positive (+) jumper cable to the positive (+) battery terminal on the disabled loader first DO NOT allow the positive clamps to touch any metal other than the positive (+) battery terminals The battery may be easily accessed by remov 43
3 Connect the other end of the positive jumper cable to the jumper vehicle’s battery positive (+) terminal 43
4 Connect the negative (-) jumper cable to the jumper vehicle’s battery negative (-) terminal 43
5 Make the final negative (-) jumper cable connection to the disabled loader’s engine block or loader frame (ground) – NOT to the disabled battery’s negative post If connected to the engine, keep the jumper clamp away from the battery, fuel l 43
6 Start the loader If it does not start at once, start the jumper vehicle engine to avoid excessive drain on the booster battery 43
7 After the disabled loader is started and running smoothly, have the second person remove the jumper cables (negative (-) jumper cable first) from the jumper vehicle’s battery and then from the disabled loader while being sure NOT to short the tw 43
Changing Attachments 44
Connecting Attachments 44
1 Manual hitch: Rotate the latch levers until the handles are vertical to disengage the lock pins 44
Figure 16 Manual Hitch – disengaged 44
1 Latch Levers 44
2 Latch Pins 44
2 Power hitch: Activate the switch to unlock the hitch and fully retract the latch pins 44
Figure 17 Power Hitch – disengaged 44
1 Pin Flags 44
2 Latch Pins 44
3 Start the engine Be sure the lift arm is lowered and in contact with the loader frame 44
4 Align the loader squarely with the back of the attachment 44
5 Tilt the hitch forward until the top edge of the hitch is below the flange on the back side of the attachment and centered between the vertical plates 44
6 Slowly drive the loader forward and, at the same time, tilt the hitch back to engage the flange on the back side of the attachment 44
7 Stop forward travel when the flange is engaged, but continue to tilt the hitch back to lift the attachment off the ground 44
8 Exercise the Mandatory Safety Shutdown Procedure (page 6) Exit the operator’s compartment and rotate the latch levers to the horizontal position to fully engage the latch pins 44
Connecting Auxiliary Hydraulic Couplings 45
Removing Attachments 45
1 Tilt the hitch back until the attachment is off the ground 45
2 Exercise the Mandatory Safety Shutdown Procedure (page 6) 45
3 With the engine off, leave the operator’s compartment and disconnect the auxiliary hydraulic hoses 45
4 Manual hitch: Rotate the hitch latch levers to the vertical position to fully retract the latch pins 45
5 Start the engine and be sure that the lift arm is fully lowered and in contact with the loader frame 45
6 Tilt the hitch forward and slowly back the loader away until the attachment is free from the loader 45
Self-Leveling 45
Using a Bucket 46
Driving over Rough Terrain 46
Driving on an Incline 46
Digging with a Bucket 46
Figure 18 Digging 46
Loading a Bucket 46
Figure 19 Loading 46
Dumping the Load onto a Pile 47
Dumping the Load into a Truck (or Hopper) 47
Figure 20 Dumping into a Truck (or Hopper) 47
Dumping the Load over an Embankment 47
Scraping with a Bucket 47
Figure 21 Scraping 47
Leveling the Ground 48
Figure 22 Leveling the Ground 48
Vibration Information 48
This section will cover primarily WBV issues, because evaluations have shown that operation of mobile compact construction equipment on jobsites typically results in HAV levels less than the allowed exposure limit of 2 5 m/s2 48
Vibration Measurement and Actions 49
1 Train operators 49
2 Choose proper equipment for the job 49
3 Maintain the work site 49
4 Maintain the equipment 49
Vibration Levels 50
Figure 23 – Vibration measurement axes 50
Highway Travel 51
Storing the Loader 51
1 Fully inflate the tires 51
2 Lubricate all grease zerks 51
3 Check all fluid levels and replenish as necessary 51
4 Add stabilizer to the fuel per the fuel supplier’s recommendations 51
5 Remove the battery, charge fully and store in a cool, dry location 51
6 Protect against extreme weather conditions such as moisture, sunlight and temperature 51
Removing Loader from Storage 51
1 Check the tire air pressure and inflate the tires if they are low 51
2 Connect the battery 51
3 Check the fan belt tension 51
4 Check all fluid levels (engine oil, transmission/hydraulic oil, engine coolant and any attached implements) 51
5 Start the engine Observe all gauges If all gauges are functioning properly and reading normal, move the machine outside 51
6 Once outside, park the machine and let the engine idle for at least five minutes 51
7 Shut the engine off and walk around machine Make a visual inspection looking for evidence of leaks 51
Transporting the Loader 52
1 Place blocks at the front and rear of the hauling vehicle’s tires 52
Figure 24 Front Tie-Down/Front Retrieval 52
2 If the loader has an attachment, lift it slightly off the ground 52
3 Back the loader slowly and carefully up the ramp onto the vehicle 52
4 Lower the loader attachment to the vehicle deck, turn off the engine and remove the key 52
5 Fasten the loader to the hauling vehicle at the points indicated by the tie-down decals (Figure 24 and Figure 25) 52
Figure 25 Rear Tie-Down/Rear Retrieval 52
6 Measure the clearance height of the loader and hauling vehicle Post the clearance height in the cab of the vehicle 52
Lifting the Loader 53
Figure 26 Single-Point Lift Eye 53
1 Using suitable lift equipment, hook into the lift eyes Adjust the length of the slings or chains to lift the loader level 53
Figure 27 Front Four-Point Lift Eyes 53
2 Center the hoist over the ROPS/ FOPS To prevent shock loading of the equipment and excessive swinging, slowly lift the loader off the ground Perform all movements slowly and gradually As needed, use a tag line to help position the loader 53
Figure 28 Right Rear Four-Point Lift Eye (Left same) 53
Notes 54
Service 55
Dealer Services 55
Replacement Parts 56
Loader Raising Procedure 56
1 To block the loader, obtain enough solid wooden or metal blocks so all of the tires are raised off the ground 56
Figure 29 Loader Properly Blocked (Tires and wheels removed to show blocks) 56
2 Using a jack or hoist capable of lifting the fully-equipped weight of the loader (with all attached options), lift the rear of the loader until the rear tires are off the ground 57
3 Stack wooden blocks under the flat part of the loader chassis They should run parallel with, but not touch, the rear tires 57
4 Slowly lower the loader until its weight rests on the blocks If the tires still touch the ground, raise the loader again, add more blocks and lower again 57
5 Repeat steps 2 through 4 for the front end When the procedure is finished, all four tires are off the ground, so they could be removed 57
Loader Lowering Procedure 57
1 Using a jack or hoist, raise the front of the loader until its weight no longer rests on the front blocks 57
2 Carefully remove the blocking under the front of the loader 57
3 Slowly lower the loader until the front tires are resting on the ground 57
4 Repeat steps 1 through 3 for the rear of the loader When the procedure is finished, all four tires will be on the ground and the blocks removed from under the loader 57
Engine Compartment Access 57
Figure 30 Engine Compartment Access Door and Cover 57
Tilting Back the ROPS/FOPS 58
Figure 31 ROPS/FOPS Lock Mechanism – Engaged 58
Adjustments 58
Control Handles 58
Removing Foreign Material 58
Lubrication 59
Figure 32 Service Locations 60
Chaincases 61
Checking and Adding Oil 61
1 Park the loader on a level surface Stop the engine 61
2 Remove the fill check plug (Figure 33) from each chaincase cover The oil level should be at the plug level or no more than 1/4 in (6 mm) below 61
Figure 33 Fill Plug Location 61
3 If the level is low, add fluid through the fill plug (Figure 33) until the oil level reaches the check plug hole Reinstall the plugs 61
Draining Oil 61
1 Park the loader on a level surface, or on a sloping surface with the loader facing downhill and the tires blocked 61
Figure 34 Drain Plug 61
2 Remove the drain plug on each chaincase (Figure 34) and drain the oil into a suitable container 61
3 Reinstall and tighten the drain plugs 61
4 Refill the chaincases at the fill plugs 61
Drive Chains 62
Checking Chain Tension 62
1 Raise the loader following the Loader Raising Procedure (page 52) 62
2 Rotate each tire by hand The proper amount of chain defection should be 1/8 in to 1 in (3 to 25 mm) forward and rearward If the chain defection is more than 1 in (25 mm) or less than 1/8 in (3 mm) in either direction, the chains should be ad 62
Adjusting Chain Tension 62
1 Raise the loader following the Loader Raising Procedure (page 52) 62
2 Remove the tire from the axle to be adjusted 62
3 Loosen (but DO NOT remove) the bolts holding the axle to the chaincase 62
4 Front Chain Tension – To tighten the front chain, move the front axle assembly toward the front of the loader To loosen the chain, move the front axle assembly toward the rear of the loader 62
5 After proper tension is achieved, retighten the bolts 62
6 Reinstall the tire 62
7 Repeat steps 2 through 6 for any other axle requiring adjustment 62
8 Lower the loader following the Loader Lowering Procedure (page 53) 62
Engine Air Cleaner 62
Figure 35 Dual-Element Air Cleaner 63
1 Restriction Indicator 63
2 Element Housing 63
3 Mounting Bracket 63
4 Inner Filter Element 63
5 Outer Filter Element 63
6 Element Cover 63
7 Dust Ejector 63
Access 63
1 Open the engine cover and then the rear door (page 53) 63
2 Unlatch the three clamps on the air cleaner and remove the cover Clean out any dirt built up in the cover assembly 63
Outer Element 63
1 Carefully pull the outer element out of the housing Never remove the inner element unless it is to be replaced 63
2 Clean out any dirt built up in the housing Leave the inner element installed during this step to prevent debris from entering the engine intake manifold 63
3 Use a trouble light inside the outer element to inspect for bad spots, pinholes or ruptures Replace the outer element if any damage is noted The outer element must be replaced if it is oil- or soot-laden 63
Inner Element 64
Reinstallation 64
1 Check the inside of the housing for any damage that may interfere with the elements 64
2 Be sure that the element sealing surfaces are clean 64
3 Insert the element(s), making sure that they are seated properly 64
4 Secure the cover to the housing with the three clamps 64
5 Check the hose connections and make sure they are all fitted and tightened properly 64
6 Reset the indicator by pressing the reset button 64
Engine Service 65
Figure 36 Engine Service Components 65
1 Muffler 65
2 Air Cleaner 65
3 Coolant Recovery Tank 65
4 Radiator/Cooler 65
5 Engine Oil Filter 65
6 Water Separator 65
7 Fuel Filter 65
8 Engine Oil Drain 65
9 Engine Oil Fill Cap 65
10 Engine Oil Dipstick 65
Checking Engine Mounting Hardware 66
Checking Engine Oil Level 66
Changing Engine Oil and Filter 66
Figure 37 Remote Engine Oil Drain 66
Changing Fuel Filter 66
Checking the Water Separator 66
Engine Diagnostic Chart 67
Figure 38 Flashing Patterns of the Failure Lamp 67
Engine Diagnostic Chart (cont ) 68
Engine Diagnostic Chart (cont ) 69
Engine Diagnostic Chart (cont ) 70
Hydraulic System 71
Checking Hydraulic Oil Level 71
Figure 39 Sight Gauge and Fill Tube 71
Changing Hydraulic Oil Filter 71
Figure 40 Hydraulic Oil Filter and Indicator 71
1 Turn off the engine 71
2 Open the reservoir drain plug located on the inside bottom of the right riser 71
3 Drain the oil to a level below the point where the filter attaches to the reservoir 71
4 Replace the reservoir drain plug 71
5 Spin off the old hydraulic filter element and spin on the new filter element 71
6 Tilt back the ROPS/FOPS 71
7 Refill the hydraulic oil reservoir with oil Refer to the Lubrication chart (page 55) 71
Changing Hydraulic Oil 72
1 Install a catch pan of sufficient capacity under the oil reservoir See page 55 72
2 Remove the drain plug located on the bottom front of the oil reservoir, behind the right rear tire Allow the oil to drain 72
3 Reinstall the drain plug 72
4 Change the oil filter 72
5 Refill the reservoir Refer to the Lubrication topic (page 55) 72
6 Start the engine and operate the hydraulic controls 72
7 Stop the engine and check for leaks at the filter and reservoir drain plug 72
8 Check the fluid level and add fluid if needed 72
Bucket Cutting Edge 72
Alternator/Fan Belt 72
Wheel Nuts 72
Lift Arm Pivots 72
Cooling System 73
Cleaning the Cooling System 73
Tires 73
Checking Tire Pressure 74
Heater/Air Conditioner Filters 74
Electrical System 75
Fuse Panel 75
Battery 75
1 Immediately remove any clothing on which acid spills 75
2 If acid contacts the skin, rinse the affected area with running water for 10 to 15 minutes 75
3 If acid contacts the eyes, flood the eyes with running water for 10 to 15 minutes See a doctor at once Never use any medication or eye drops unless prescribed by the doctor 75
4 To neutralize acid spilled on the floor, use one of the following mixtures: 75
a 1 pound (0 5 kg) of baking soda in 1 gallon (4 L ) of water, or 75
b 1 pint (0 5 L) of household ammonia in 1 gallon (4 L) of water 75
Notes 76
Troubleshooting 77
Notes 86
Maintenance 87
Maintenance Log 88
Maintenance Log 89
Maintenance Log 90
Specifications 91
Loader Specifications 91
Standard Features 94
Optional Features 94
Dimensional Specifications 95
67 5 in (1715 mm), 16 8 cu ft (0 48 m3) Earth and Foundry with High Back Bucket w/12 x 16 5 Tires 95
inches 95
mm 95
A 95
164 5 95
4178 95
B 95
123 1 95
3126 95
C 95
80 5 95
2045 95
D 95
134 1 95
3406 95
E 95
39 9o 95
F 95
92 2 95
2342 95
G 95
31 8 95
808 95
J 95
24 1o 95
M 95
91 1o 95
O 95
40 2 95
1021 95
P 95
43 2 95
1097 95
Q 95
66 3 95
1684 95
R 95
69 8 95
1773 95
S 95
7 6 95
193 95
V 95
99 1 95
2517 95
W 95
20 7o 95
X 95
84 0 95
2134 95
Y 95
49 3 95
1252 95
Z 95
62 95
1575 95
75 in (1905 mm), 18 2 cu ft (0 52 m3) Earth and Foundry with High Back Bucket w/12 x 16 5 Tires 96
inches 96
mm 96
A 96
164 3 96
4173 96
B 96
123 2 96
3129 96
C 96
81 2 96
2062 96
D 96
138 8 96
3526 96
E 96
38 2o 96
F 96
91 6 96
2327 96
G 96
36 0 96
914 96
J 96
26 6o 96
M 96
90 4o 96
O 96
40 6 96
1031 96
P 96
48 4 96
1229 96
Q 96
66 3 96
1684 96
R 96
69 1 96
1755 96
S 96
7 6 96
193 96
V 96
104 3 96
2649 96
W 96
21 1o 96
X 96
86 3 96
2192 96
Y 96
52 2 96
1326 96
Z 96
65 5 96
1664 96
Capacities and Ratings 97
2066/2076/2086 (2076 EU/2086 EU) 97
Weight 97
2066/2076 Rating 97
2086 Rating 97
465 lbs (211 kg) 97
1915 lbs (869 kg) 97
2280 lbs (1034 kg) 97
500 lbs (227 kg) 97
1919 lbs (870 kg) 97
2265 lbs (1027 kg) 97
525 lbs (238 kg) 97
1904 lbs (863 kg) 97
2217 lbs (1006 kg) 97
645 lbs (293 kg) 97
1687 lbs (765 kg) 97
2010 lbs (912 kg) 97
595 lbs (270 kg) 97
1748 lbs (793 kg) 97
2102 lbs (954 kg) 97
750 lbs (340 kg) 97
1719 lbs (780 kg) 97
2072 lbs (940 kg) 97
789 lbs (358 kg) 97
1930 lbs (875 kg) 97
2301 lbs (1044 kg) 97
512 lbs (232 kg) 97
1896 lbs (860 kg) 97
2269 lbs (1029 kg) 97
475 lbs (216 kg) 97
2028 lbs (944 kg) 97
2395 lbs (1086 kg) 97
383 lbs (174 kg) 97
2285 lbs (1037 kg) 97
2687 lbs (1219 kg) 97
480 lbs (218 kg) 97
2196 lbs (996 kg) 97
2646 lbs (1200 kg) 97
500 lbs (227 kg) 97
2180 lbs (989 kg) 97
2585 lbs (1173 kg) 97
Weight 98
2066/2076 Rating 98
2086 Rating 98
492 lbs (223 kg) 98
1624 lbs (737 kg) 98
1913 lbs (868 kg) 98
492 lbs (223 kg) 98
1519 lbs (689 kg) 98
1807 lbs (820 kg) 98
492 lbs (223 kg) 98
1441 lbs (654 kg) 98
1711 lbs (776 kg) 98
Common Materials and Densities 99
Material 99
Density 99
lbs /cu ft 99
kg/m3 99
35-50 99
560-800 99
112 99
1792 99
110 99
1760 99
23 99
368 99
80-100 99
1280-1600 99
53-63 99
848-1008 99
115 99
1840 99
50 99
800 99
94 99
1504 99
30 99
480 99
70-90 99
1121-1442 99
80-100 99
1281-1602 99
93-111 99
1488-1776 99
100 99
1602 99
120 99
1922 99
115 99
1840 99
145 99
2320 99
60 99
960 99
90 99
1440 99
65 99
1040 99
45 99
720 99
47 99
752 99
90 99
1440 99
68 99
1088 99
110 99
1760 99
100 99
1602 99
135 99
2160 99
108 99
1728 99
125 99
2000 99
95 99
1520 99
90 99
1440 99
70 99
1120 99
15-50 99
240-800 99
107 99
1712 99
Bucket Selection 100
Torque Specifications 101
MUSTANG MANUFACTURING COMPANY, INC 102
Warranty 102
MUSTANG WARRANTY SERVICE INCLUDES: 102
MUSTANG WARRANTY DOES NOT INCLUDE: 102
Index 103
A 103
B 103
C 103
D 103
E 103
F 103
G 103
H 103
I 104
J 104
L 104
M 104
O 104
P 104
R 104
S 104
T 104
V 105
W 105
IMAGES PREVIEW OF THE MANUAL:
VIDEO PREVIEW OF THE MANUAL:
PLEASE NOTE:
- This is the SAME exact manual used by your dealers to fix your vehicle.
- The same can be yours in the next 2-3 mins as you will be directed to the download page immediately after paying for the manual.
- Any queries / doubts regarding your purchase, please feel free to contact [email protected]
S.V
