Mustang 2056 Skid-Steer Loader Operator’s Manual 917402-DP0310 – PDF DOWNLOAD
IMAGES PREVIEW OF THE MANUAL:
FILE DETAILS:
Mustang 2056 Skid-Steer Loader Operator’s Manual 917402-DP0310 – PDF DOWNLOAD
Language : English
Pages : 102
Downloadable : Yes
File Type : PDF
Size: 2.49 MB
TABLE OF CONTENTS:
Mustang 2056 Skid-Steer Loader Operator’s Manual 917402-DP0310 – PDF DOWNLOAD
Multi-Tach, and Hydraglide are trademarks of Mustang Manufacturing Company, Inc Power-A-Tach is a registered trademark of the Mustang Manufacturing Company, Inc Hydraloc is a trademark of Gehl Company 3
2056 Skid-Steer Loader Operator’s Manual 3
Hand/Foot Control 37
1 Left Drive Control Handle 37
2 Right Drive Control Handle 37
3 Lift Control Pedal 37
4 Tilt Control Pedal 37
Drive Controls 37
Lift/Tilt Controls 38
Dual-Hand Controls 39
Figure 14 Dual-Hand Controls 39
1 Left Drive Control Handle 39
2 Right Drive Control Handle 39
Drive Controls 39
Lift/Tilt Controls 39
Introduction 5
Loader Identification 7
1 Front Work Lights 7
2 Restraint Bar 7
3 Lift Arm 7
4 Lift Cylinder 7
5 Tires 7
6 Attachment Bracket 7
7 Tilt Cylinders 7
8 Handholds 0
1 Roll-Over/Falling Object Protective Structure (ROPS/FOPS) 7
2 Engine Cover 7
3 Rear Work Lights 7
4 Tail Lights 7
5 Rear Door 7
Control/Indicator Symbols 8
Power Off 8
Power On 8
Engine Start 8
Battery Charge 8
Electrical Power 8
Worklight w/Flasher 8
Worklight 8
Safety Alert 8
Hazard Flasher 8
Seatbelt 8
Horn 8
Read Operator’s Manual 8
Volume – Full 8
Volume – Half Full 8
Volume – Empty 8
H-L 8
High – Low 8
N 8
Neutral 8
F 8
Forward 8
R 8
Reverse 8
Parking Brake 8
Engine Air Filter 8
Engine Oil 8
Engine Oil Filter 8
Engine Oil Pressure 8
Fuel Filter 8
Engine Temperature 8
Hydraulic System 8
Hydraulic Oil Temperature 8
Hydraulic Oil Filter 8
Grease Lubrication Point 8
Glow Indicator Lamp 8
Diesel Fuel 8
Chaincase Oil 8
Clockwise Rotation 8
Counterclockwise Rotation 8
Fast 8
Slow 8
Ride Control 8
Power Hitch 8
Bucket – Float 8
Bucket – Rollback 8
Bucket – Dump 8
Lift Arm – Lower 8
Lift Arm – Raise 8
Service Hours 8
Lift Point 8
Tie-Down 8
Diesel Water Separator 8
Engine Malfunction Shutdown 8
Safety 9
Mandatory Safety Shutdown Procedure 10
1 Move the drive control handle(s) to the neutral position 10
2 Lower the lift arm and attachment completely If the lift arm must be left in the raised position, be sure to properly engage the lift arm support device (page 22) 10
3 Move the throttle to the low idle position, shut off the engine and remove the key 10
4 Before exiting, move the lift/tilt control(s) to verify that the controls do not cause movement of the lift arm or hitch 10
Safety Reminders 10
Potential Hazards 12
Safety Decals 12
New Decal Application 12
ANSI-Style Safety Decals inside the ROPS/FOPS 13
ANSI-Style Safety Decals on the outside of the Loader 14
ANSI-Style Safety Decals on the outside of the Loader 15
ANSI-Style Safety Decals in the Engine Compartment 16
ISO-Style (used Internationally) Safety Decals inside the ROPS/FOPS 17
ISO-Style (used Internationally) Safety Decals on the outside of the Loader 18
ISO-Style (used Internationally) Safety Decals on the outside of the Loader 19
ISO-Style (used Internationally) Safety Decals in the Engine Compartment 20
Product and Component Plate Locations 21
Controls and Safety Equipment 23
Guards and Shields 23
Operator Restraint Bar 23
Operator’s Seat 24
Figure 1 Operator’s Seat 24
1 Restraint Bar 24
2 Seatbelt 24
3 Seat Position Adjustment Lever 24
4 Suspension Seat Weight Adjustment Knob (optional) 24
Upper-Torso Restraint 24
Safety Interlock System 24
Hydraloc™ System 24
Testing the Safety Interlock System 25
ROPS/FOPS 25
Parking Brake 25
Figure 2 Parking Brake Switch 25
Horn 25
Rear Window Emergency Exit 26
Lift Arm Support Device 26
Engagement 26
Figure 3 Lift Arm Support Device Engaged 26
1 Lower the lift arm fully 26
2 Stop the engine 26
3 Leave the operator’s compartment Remove the lock pin holding the support device up against the lift arm Allow the support device to contact the lift cylinder 26
4 Return to operator’s compartment and restart the engine 26
5 Use the lift control to raise the lift arm until the support device drops over the end of the lift cylinder and around the cylinder rod Slowly lower the lift arm until the free end of the support device contacts the top end of the lift cylinder 26
6 Look to make sure the support device is securely against the cylinder end Then, stop the loader engine, remove the key and leave the operator’s compartment 26
Disengagement 27
1 Start the engine; 27
2 Raise the lift arm fully; 27
3 Stop the engine; 27
4 Before leaving the operator’s compartment, check to make sure that the lift arm is being held in the raised position by the solenoid valve (See Note below) 27
Figure 4 Lift Arm Support Device Storage Location 27
5 To store the support device, raise it up until it contacts the lift arm Secure the lift arm support devise with the lock pin 27
Accessory Plug 27
Dome Light 27
Work Lights 27
Heater (optional) 28
Heater and Air Conditioner (optional) 28
Figure 5 Heater/ Air Conditioner Controls 28
1 Fan Speed: Controls the rate at which air exits the vents 28
2 Heater/Air Conditioner (HVAC) Selector Switch: Turns on either the heater or air conditioner Center “off” position allows fan-only operation for air circulation 28
Tips For Improving Heater Performance 28
1 Inside the engine compartment, close off the cold air intake on the heater box 28
2 Inspect the cab recirculation air filter for excess dirt build-up 28
3 Inspect the heater hoses for twists, kinks or pinched areas 28
4 Ensure the heater valves are fully open On heater-only units, the coolant is controlled by a manual valve On HVAC units, the coolant is controlled by a manual valve and an electric solenoid valve 28
5 Run the engine at a mid-throttle position (see note) Running the engine at low idle may not be enough load to bring the engine up to its full thermostat temperature (188 F, or 87 C) depending upon ambient conditions 28
Engine Speed Control 29
Figure 6 Hand Throttle Lever 29
Figure 7 Foot Throttle 29
Two-Speed Transmission (optional) 30
Hydraglide™ Ride Control System (optional) 30
Auto-Shutdown System 30
Attachment Mounting 31
Multi-Tach™ Hitch 31
Figure 8 Multi-Tach™ Hitch 31
Power-A-Tach® Hitch 31
Figure 9 Power-A-Tach® Hitch 31
Instrument Panels 32
Figure 10 Left Panel 32
Left Panel 32
1 Two-Speed Transmission (optional) – Lights when high speed is engaged 32
2 Parking Brake – Lights when the parking brake is applied 32
3 Power-A-Tach® Hitch (optional) – Used to operate the Power-A-Tach® hitch 32
4 Fan (optional) – Used to control the fan speed for the air conditioner and heater 32
5 Heater/Air Conditioner Selector – Used to control the heater and air conditioner 32
6 Accessory Plug – 12-volt DC power outlet 32
7 Hydraglide™ Ride Control System (optional) – Lights when the ride control system is activated 32
8 Float Indicator (Dual Joystick control option only) – Lights when float function is activated 32
9 Parking Brake Switch – Used to apply the parking brake 32
Right Panel 33
Figure 11 Right Panel 33
1 Hourmeter – Displays the total operating hours of the loader 33
2 Fuel Level Gauge – Displays the amount of fuel in the tank 33
3 Engine Coolant Temperature Gauge – Displays the temperature of the engine coolant 33
4 Engine Coolant Temperature – Lights if the engine coolant is too hot This warns the operator to stop the engine and determine and correct the cause for the high temperature During normal operation this indicator should be OFF 33
5 Hydraulic Oil Temperature – Lights if the hydraulic oil is too hot This warns the operator to reduce the hydraulic load and determine the cause of the high temperature During normal operation this indicator should be OFF 33
6 Light Switch – Controls all the lights on the loader Symbols denote the four positions of the light switch In a clockwise direction these are: 33
7 High-Flow Auxiliary Switch (optional) – Controls the direction of hydraulic oil flow Push the right side of the rocker switc 33
8 Keyswitch – In a clockwise rotation, these positions are: 33
9 Circuit Breakers – Four circuit breakers on the instrument panel protect the loader electrical circuits 34
10 Fasten Seatbelt – A momentary visual (and audible) indicator to remind the operator to fasten the seatbelt(s) 34
11 Engine Oil Pressure – Lights if the engine oil pressure is too low Warns the operator to immediately stop the engine and determine the cause for the low pressure During normal operation this indicator should be OFF 34
12 Battery – Lights if the charging voltage is too high or too low During normal operation this indicator should be OFF 34
13 Preheat Indicator Lamp – Lights when the engine preheat is active During normal operation this indicator should be OFF 34
Joystick Controls 35
Figure 12 Joystick Controls 35
1 Lift/Tilt Control 35
2 Drive Control 35
Drive Control 35
Lift/Tilt Control 36
Auxiliary Hydraulic System 40
Standard-Flow Auxiliary Hydraulic Control 40
Figure 16 Dual Joystick Electric Auxiliary Control 40
Figure 17 Hand/Foot Auxiliary Control 41
High-Flow Auxiliary Hydraulic Control (optional) 41
Figure 18 High-Flow Auxiliary Switch 41
Operation 43
Before Starting the Engine 43
Starting the Engine 43
1 Carefully step up onto the back of the bucket or attachment and grasp the handholds to get into the operator’s compartment 43
2 Fasten the seatbelt(s) and lower the restraint bar 43
3 Verify the following: 43
4 Push the throttle lever forward to approximately half speed 43
5 Turn the key to the start position 43
Cold-Starting 44
Cold-Starting Procedure 44
1 Turn the key to the run position If the preheat light on the right instrument panel comes on, wait until it goes out 44
2 Turn the key switch to the start position 44
3 Repeat if engine does not start 44
Stopping the Loader 44
1 Check that the drive control handle is in neutral position; 44
2 Lower the lift arm and rest the attachment on the ground; 44
3 Pull back the throttle lever to the low idle position (and remove foot from the throttle pedal); 44
4 Wait for the turbocharger to slow, and them turn the keyswitch to the off position and remove the key; and 44
5 Raise the restraint bar, unfasten the seatbelt(s) Verify that movement of the controls, does not cause machine movement, and then grasp the handholds while climbing out of the operator’s compartment 44
Parking the Loader 45
Jump-Starting 45
1 Turn the keyswitches of both vehicles to OFF Be sure both vehicles are in “neutral” and NOT touching each other 45
2 Connect the positive (+) jumper cable to the positive (+) battery terminal on the disabled loader first DO NOT allow the positive clamps to touch any metal other than the positive (+) battery terminals 45
3 Connect the other end of the positive jumper cable to the jumper vehicle’s battery positive (+) terminal 45
4 Connect the negative (-) jumper cable to the jumper vehicle’s battery negative (-) terminal 45
5 Make the final negative (-) jumper cable connection to the disabled loader’s engine block or loader frame (ground) – NOT to t 45
6 Start the loader If it does not start at once, start the jumper vehicle’s engine to avoid excessive drain on the booster battery 45
7 After the disabled loader is started and running smoothly, have the second person remove the jumper cables [negative (-) jump 45
Changing Attachments 46
Connecting Attachments 46
1 Manual hitch: Rotate the latch levers until the handles are vertical to retract the lock pins Start the loader engine 46
Figure 19 Manual Hitch – disengaged 46
1 Latch Levers 46
2 Latch Pins 46
Figure 20 Power Hitch – disengaged 46
1 Pin Flags 46
2 Latch Pins 46
2 Be sure the lift arm is lowered and in contact with the loader frame 46
3 Align the loader squarely with the back of the attachment 46
4 Tilt the hitch forward until the top edge of the hitch is below the flange on the back side of the attachment and centered between the vertical plates 46
5 Slowly drive the loader forward and, at the same time, tilt the hitch back to engage the flange on the back side of the attachment 46
6 Stop forward travel when the flange is engaged, but continue to tilt the hitch back to lift the attachment off the ground 46
7 Manual hitch: Exercise the Mandatory Safety Shutdown Procedure (page 6) Exit the operator’s compartment and rotate the latch levers to the horizontal position to fully engage the latch pins 47
8 Power hitch: Activate the switch to lock the hitch and fully engage the latch pins 47
Connecting Auxiliary Hydraulic Couplings 47
Removing an Attachment 47
1 Tilt the hitch back until the attachment is off the ground 47
2 Exercise the Mandatory Safety Shutdown Procedure (page 6) 47
3 Relieve any hydraulic pressure in the auxiliary and attachment lines: 47
a Turn the key on (do not start the engine) 47
b With the restraint bar down, move the auxiliary hydraulic control back and forth This will relieve the pressure in the hydraulic system 47
4 With the engine off, leave the operator’s compartment and disconnect the auxiliary hydraulic hoses 47
5 Manual hitch: Rotate the hitch latch levers to the vertical position to fully retract the latch pins 47
6 Start the engine and be sure that the lift arm is fully lowered and in contact with the loader frame 47
7 Tilt the hitch forward and slowly back the loader away until the attachment is free from the loader 47
Self-Leveling 48
Using a Bucket 48
Driving Over Rough Terrain 48
Driving On an Incline 48
Digging with a Bucket 48
Figure 21 Digging 48
Loading a Bucket 49
Figure 22 Loading 49
Dumping the Load Onto a Pile 49
Dumping the Load into a Truck or Hopper 49
Figure 23 Dumping into a Truck or Hopper 49
Dumping the Load Over an Embankment 49
Scraping with a Bucket 50
Figure 24 Scraping 50
Leveling the Ground 50
Figure 25 Leveling the Ground 50
Vibration Information 51
Vibration Measurement and Actions 51
1 Train operators 52
2 Choose proper equipment for the job 52
3 Maintain the work site 52
4 Maintain the equipment 52
Vibration Levels 53
Figure 26 Vibration measurement axes 53
Highway Travel 54
Storing the Loader 54
1 Fully inflate the tires 54
2 Lubricate all grease zerks 54
3 Check all fluid levels and replenish as necessary 54
4 Add stabilizer to the fuel per the fuel supplier’s recommendations 54
5 Remove the battery, charge it fully and store it in a cool, dry location 54
6 Protect against extreme weather conditions such as moisture, sunlight and temperature 54
Removing Loader from Storage 54
1 Check the tire air pressure and inflate the tires if they are low 54
2 Reconnect the battery 54
3 Check the fan belt tension 54
4 Check all fluid levels (engine oil, transmission/hydraulic oil, engine coolant and any attached implements) 54
5 Start the engine Observe all gauges If all gauges are functioning properly and reading normal, move the machine outside 54
6 Once outside, park the machine and let the engine idle for at least five minutes 54
7 Shut the engine off and walk around machine Make a visual inspection looking for evidence of leaks 54
Transporting the Loader 55
1 Block the front and rear of the hauling vehicle’s tires 55
Figure 27 Front Tie-Down/ Retrieval Points 55
2 If the loader has an attachment, lift it slightly off the ground 55
3 Back the loader slowly and carefully up the ramps onto the hauling vehicle 55
4 Lower the loader attachment to the vehicle deck, turn off the engine and remove the key 55
5 Fasten the loader to the hauling vehicle at the points indicated by the tie-down decals (Figure 27 and Figure 28) 55
Figure 28 Rear Tie-Down/ Retrieval Points 55
6 Measure the clearance height of the loader and hauling vehicle Post the clearance height in the cab of the hauling vehicle 55
Lifting the Loader 56
Figure 29 Single-Point Lift Eye 56
1 Using suitable lift equipment, hook into the lift eyes Adjust the length of the slings or chains to lift the loader level 56
Figure 30 Front Four-Point Lift Eyes 56
2 Center the hoist over the ROPS/FOPS To prevent shock loading of the equipment and excessive swinging, slowly lift the loader 56
Figure 31 Right Rear Four-Point Lift Eye (left same) 56
Service 57
Dealer Services 57
Replacement Parts 58
Loader Raising Procedure 59
1 To block the loader, obtain enough solid wooden or metal blocks, so that when stacked, all of the tires are raised off the ground 59
Figure 32 Loader Properly Blocked (Tires and wheels removed to show blocks) 59
2 Using a jack or hoist capable of lifting the fully-equipped loader (with all attached options), lift the rear of the loader until the rear tires are off the ground 59
3 Stack wooden blocks under the flat part of the loader chassis They should run parallel with, but not touch, the rear tires 59
4 Slowly lower the loader until its weight rests on the blocks If the tires still touch the ground, raise the loader again, add more blocks and lower again 59
5 Repeat Steps 2 through 4 for the front end When the procedure is finished, all four tires are off the ground, so they could be removed 59
Loader Lowering Procedure 60
1 Using a suitable jack or hoist, raise the front of the loader until its weight no longer rests on the front blocks 60
2 Carefully remove the blocking under the front of the loader 60
3 Slowly lower the loader until the front tires are resting on the ground 60
4 Repeat Steps 1 through 3 for the rear of the loader When the procedure is finished, all four tires will be on the ground and the blocks removed from under the loader 60
Engine Compartment Access 60
Figure 33 Engine Compartment Access Doors 60
Tilting Back the ROPS/FOPS 61
Figure 34 ROPS/FOPS Lock Mechanism – Engaged 61
Adjustments 61
Control Handles 61
Fuel Sender 61
Engine Speed Control 62
Foreign Material Removal 62
Lubrication 62
Figure 35 Service Locations 64
Chaincases 65
Checking and Adding Oil 65
1 Park the loader on a level surface Stop the engine 65
Figure 36 Fill and Check Plug Location 65
2 Remove the fill and check plug (Figure 36) from each chaincase cover The oil level should be no more than 1/4 in (6 mm) below the plug 65
3 If the level is low, add fluid through the fill and check plug (Figure 36) until the oil level reaches the check plug hole Reinstall the plug 65
Draining Oil 65
1 Park the loader on a level surface, or on a sloping surface with the loader facing downhill and the tires blocked 65
Figure 37 Drain Plug 65
2 Remove the drain plug (Figure 37) on each chaincase and drain the oil into a suitable container 65
3 Reinstall and tighten the drain plugs 65
4 Refill the chaincases at the fill plugs 65
Drive Chains 65
Checking Chain Tension 65
1 Raise the loader following the Loader Raising Procedure (page 55) 65
2 Rotate each tire by hand The proper amount of chain defection should be 1/8 in to 1 in (3 to 25 mm) forward and rearward 65
Adjusting Chain Tension 65
1 Raise the loader following the Loader Raising Procedure (page 55) 65
2 Remove the tire from the axle to be adjusted 65
3 Loosen (but DO NOT remove) the bolts holding the axle to the chaincase 65
4 Front Chain Tension – To tighten the front chain, move the front axle assembly toward the front of the loader To loosen the chain, move the front axle assembly toward the rear of the loader 66
5 After proper tension is achieved, retighten the bolts 66
6 Reinstall the tire 66
7 Repeat Steps 2 through 6 for any other axle requiring adjustment 66
8 Lower the loader following the Loader Lowering Procedure (page 56) 66
Engine Air Cleaner 67
Figure 38 Dual-Element Air Cleaner 67
1 Restriction Indicator 67
2 Element Housing 67
3 Inner Filter Element 67
4 Outer Filter Element 67
5 Element Cover 67
6 Dust Ejector 67
Changing the Air Cleaner Elements 67
1 Open the engine cover and then the rear door (page 56) 67
2 Unlatch the three latches on the air cleaner and remove the cover Clean out any dirt built up in the cover assembly 67
Outer Element 68
1 Carefully pull the outer element out of the housing Never remove the inner element unless it is to be replaced 68
2 Clean out any dirt built up in the housing Leave the inner element installed during this step to prevent debris from entering the engine intake manifold 68
3 Use a trouble light inside the outer element to inspect for bad spots, pinholes or ruptures Replace the outer element if any damage is noted The outer element must be replaced if it is oil- or soot-laden 68
Inner Element 68
Reinstallation 68
1 Check the inside of the housing for any damage that may interfere with the elements 68
2 Be sure that the element sealing surfaces are clean 68
3 Insert the element(s), making sure that they are seated properly 68
4 Secure the cover to the housing with the three clamps 68
5 Check the hose connections and make sure they are all clamped and tightened properly 68
6 Reset the indicator by pressing the reset button 68
Engine Service 68
Checking Engine Mounting Hardware 68
Checking Engine Oil Level 69
Figure 39 Engine Service Components 69
1 Radiator/Cooler 69
2 Engine Oil Filter 69
3 Muffler 69
4 Engine Oil Fill Cap 69
5 Engine Oil Dipstick 69
6 Air Cleaner 69
7 Fuel Filter 69
8 Engine Oil Drain Valve 69
Changing Engine Oil and Filter 69
Figure 40 Remote Engine Oil Drain 69
Changing Fuel Filter 70
Hydraulic System 70
Checking Hydraulic Oil Level 70
Figure 41 Sight Gauge and Fill Tube 70
Changing Hydraulic Oil Filter 71
Figure 42 Hydraulic Oil Filter and Indicator 71
1 Turn off the engine 71
2 Open the reservoir drain plug located on the inside bottom of the right riser 71
3 Drain the oil to a level below the point where the filter attaches to the reservoir 71
4 Replace the reservoir drain plug 71
5 Spin off the old hydraulic filter element and spin on the new filter element 71
6 Refill the hydraulic oil reservoir with oil Refer to the Lubrication chart (page 59) 71
Changing Hydraulic Oil 71
1 Place a catch pan of sufficient capacity under the oil reservoir, see page 58 71
2 Remove the drain plug located on the bottom front of the oil reservoir, behind the right rear tire Allow the oil to drain 71
3 Reinstall the drain plug 71
4 Change the oil filter 71
5 Refill the reservoir Refer to the Lubrication topic (page 58) 71
6 Start the engine and operate the hydraulic controls 71
7 Stop the engine and check for leaks at the filter and reservoir drain plug 71
8 Check the fluid level and add fluid if needed 71
Bucket Cutting Edge 71
Alternator/Fan Belt 71
Wheel Nuts 72
Lift Arm Pivots 72
Cooling System 72
Cleaning the Cooling System 72
Tires 72
Checking Tire Pressure 73
Heater Filters 73
Electrical System 74
Circuit Breakers 74
Battery 74
1 Immediately remove any clothing on which acid spills 74
2 If acid contacts the skin, rinse the affected area with running water for 10 to 15 minutes 74
3 If acid contacts the eyes, flood the eyes with running water for 10 to 15 minutes See a doctor at once Never use any medication or eye drops unless prescribed by the doctor 74
4 To neutralize acid spilled on the floor, use one of the following mixtures: 74
a 1 pound (0 5 kg) of baking soda in 1 gallon (4 L ) of water, or 74
b 1 pint (0 5 L) of household ammonia in 1 gallon (4 L) of water 74
Troubleshooting 75
Maintenance 85
Maintenance Log 86
Maintenance Log 87
Maintenance Log 88
Specifications 89
Loader Specifications 89
Standard Features 90
Optional Features 90
Dimensional Specifications 91
14 3 ft 3 (0 4 m3) Bucket w/12 x 16 5 Tires 91
1300 lbs (589 kg) 92
Common Materials and Densities 93
Material 93
Density 93
Bucket Selection 94
Torque Specifications 95
MUSTANG MANUFACTURING COMPANY, INC 96
WARRANTY 96
MUSTANG WARRANTY SERVICE INCLUDES: 96
MUSTANG WARRANTY DOES NOT INCLUDE: 96
INDEX 97
DESCRIPTION:
Mustang 2056 Skid-Steer Loader Operator’s Manual 917402-DP0310 – PDF DOWNLOAD
INTRODUCTION:
This Operator’s Manual provides the owner/operator information about maintaining and servicing Mustang 2056 skid-steer loaders. More important, this manual provides an operating plan for safe and proper use of the machine. Major points of safe operation are detailed in the Safety chapter of this manual.
- We ask that you read and understand the contents of this manual completely and become familiar with your new machine before operating it. See your authorized Mustang dealer if you have any questions concerning information in the manual, require extra manuals, or for information concerning the availability of manuals in other languages.
- Throughout this manual information is provided set in italic type and introduced by the word Note or Important. Read carefully and comply with these messages – it will improve operating and maintenance efficiency, help avoid breakdowns and damage, and extend the machine’s life.
- A manual storage box in the operator’s compartment holds the Operator’s Manual and AEM Safety Manual (also available in Spanish). Please return the manuals to this box and keep them with the unit at all times. If this machine is resold, these manuals should be given to the new owner.
- The attachments and equipment available for use with this machine have a wide variety of potential applications. Read the manual provided with the attachment to learn how to safely maintain and operate the equipment. Be sure the machine is suitably equipped for the type of work to be performed.
- Do not use this machine for any applications or purposes other than those described in this manual, or those applicable for approved attachments. If the machine is to be used with special attachments or equipment other than those approved by Mustang Manufacturing, consult your Mustang dealer.
- Anyone using non-approved attachments or making unauthorized modifications is responsible for the consequences. The Mustang dealership network stands ready to provide any assistance that may be required, including providing genuine Mustang service parts. All service parts should be obtained from your Mustang dealer. Provide complete information about the part, including the model and serial number of the machine.
- As a handy reference, record these numbers in the space provided on the Table of Contents page. Mustang Manufacturing strives to continuously improve its products, and reserves the right to make changes and improvements in the design and construction of any part without incurring the obligation to install such changes on any previously delivered units.
- If this machine was purchased “used,” or if the owner’s address has changed, please provide your Mustang dealer or Mustang Service Department with the owner’s name and current address, along with the machine model and serial number. This will allow the registered owner information to be updated, so that the owner can be notified directly in case of an important product issue, such as a safety update program.
VIDEO PREVIEW OF THE MANUAL:
PLEASE NOTE:
- This is the SAME manual used by the dealers to troubleshoot any faults in your vehicle. This can be yours in 2 minutes after the payment is made.
- Contact us at [email protected] should you have any queries before your purchase or that you need any other service / repair / parts operators manual.
S.V
