Laverda EU Harvesting 225LCS 255LCS 255LCS-LS 255LCS-LSI 256LCS 286LCS 296LCS 296LCS-LS Workshop Manual L3272313 – PDF DOWNLOAD
FILE DETAILS:
Laverda EU Harvesting 225LCS 255LCS 255LCS-LS 255LCS-LSI 256LCS 286LCS 296LCS 296LCS-LS Workshop Manual L3272313 – PDF DOWNLOAD
Language : English
Pages : 548
Downloadable : Yes
File Type : PDF
Size: 355 MB
TABLE OF CONTENTS:
Laverda EU Harvesting 225LCS 255LCS 255LCS-LS 255LCS-LSI 256LCS 286LCS 296LCS 296LCS-LS Workshop Manual L3272313 – PDF DOWNLOAD
– GENERAL INFORMATION 00
– ENGINE 10
– LIVE PTO 14
– TRANSMISSION 21
– FRONT DRIVE AXLE 25
– HYDROSTATIC TRANSMISSION 29
– BRAKES AND CONTROL 33
– HYDRAULIC SYSTEMS 35
– STEER I NG 41
– AXLE AND WHEELS 44
– CAB CLIMATE CONTROL 50
– ELECTRICAL SYSTEMS 55
– ATTACHMENTS/ HEADERS 58
– PRODUCT FEEDING 60
– THRESHING 66
– SEPARATION 72
– STRAW CHOPPER 73
– CLEANING 7 4
– GRAIN STORAGE 80
DESCRIPTION:
Laverda EU Harvesting 225LCS 255LCS 255LCS-LS 255LCS-LSI 256LCS 286LCS 296LCS 296LCS-LS Workshop Manual L3272313 – PDF DOWNLOAD
INTRODUCTORY REMARKS:
◊ This manual is subdivided in sections marked by two-digit numbers, with independent page numbering within
each section.
For a quick reference, these sections have the same identification number and the same description of the
relevant Flat Time Rate Manual.
◊ The dealt matters and the information can be easily detected by index on the following pages.
◊ At the bottom of each page there is the manual print number and the relevant publication/up-dating date.
◊ The pages of further up-datings shall have the same print number of the current publication, changing the
last digit (for example: first up-dating 327231011; second up-dating 327231012; etc.) and the relevant publication
date.
These pages shall be completed by the new print of the index, duly revised.
◊ The information of this manual are up-dated at the date of the publication.
As LA VERDA continuously improves its product range, some information could be not up-dated due to
modifications of technical or commercial type, as well as for suiting the law regulations of the different
countries.
In case of disagreement, refer to LAVERDA Sales and Service networks.
GENERAL INSTRUCTION:
IMPORTANT NOTE:
All maintenance and repair works described in this manual must be carried out only by the LAVERDA service network,
strictly complying with the instructions given and using the required special tools.
Anybody carrying out the above interventions without strictly complying with the prescriptions is fully responsible
for the occurred damage.
ADJUSTMENT SHIMS:
During any adjustment, select the adjustment shims measuring them individually, by a micrometer, and then summing
up the detected values: do not rely on the wrong measurement of the complete pack or on the rated value
stated for each ring.
ROTARY SHAFT SEALS:
For correct rotating shaft seal installation, proceed as follows:
– before assembly, leave the seals in oil bath, for at least half an hour, using the same oil they should contain;
– carefully clean the shaft and make sure its working surface isn’t damaged;
– direct the seal edge to the fluid; in case of hydrodynamic edge, the stripes must be directed so that, considering
the shaft rotation direction, the fluid is brought back to the sealing means;
– lay a thin layer of lubricant on the seal edge (oil rather than grease) and fill with grease the gap between seal
edge and dust edge in case of double edge seals;
– fit the seal in the relevant housing pressing it or using a drift with flat contact surface; do not beat it with hammer
or drift;
– during driving, make sure the seal is perpendicular to its housing and, at the end of the driving, make sure it
touches the shoulder;
– to prevent damaging the seal edge against the shaft, lay a suitable protection during installation of both parts.
“O-RINGS”:
Lubricate O-rings before fitting them in their seats to prevent any rolling over and twisting, during assembly/installation,
thus jeopardizing their sealing action.
SEALANTS:
Before laying the sealant on the mating surfaces, prepare them as follows:
– remove possible scales through a metal brush;
– thoroughly degrease the surfaces by one of the following cleansers: trichloroethylene, oil, or a solution of water
and soda.
IMAGES PREVIEW OF THE MANUAL:
VIDEO PREVIEW OF THE MANUAL:
PLEASE NOTE:
- This is the same manual used by the DEALERSHIPS to SERVICE your vehicle.
- The manual can be all yours – Once payment is complete, you will be taken to the download page from where you can download the manual. All in 2-5 minutes time!!
- Need any other service / repair / parts manual, please feel free to contact us at heydownloadss @gmail.com . We may surprise you with a nice offer
S.V