Case 1021G 1121G Stage IV Wheel Loader Operator’s Manual 51576098 – PDF DOWNLOAD
IMAGES PREVIEW OF THE MANUAL:
DESCRIPTION:
Case 1021G 1121G Stage IV Wheel Loader Operator’s Manual 51576098 – PDF DOWNLOAD
GENERAL INFORMATION :
Note to the owner :
- Read this manual before you start the engine or operate the machine. If you need more information, see your authorized
dealer. - This manual contains important information about the safe operation, adjustment, and maintenance of your machine.
- Refer to the index at the back of this manual for locating specific items about your machine. The wheel loader conforms
to current safety regulations at the time of its manufacture. - Consult an authorized dealer or CNH Industrial on changes, additions, or modifications that can be required for this
machine to comply with various country regulations and safety requirements. Unauthorized modifications will cause
serious injury or death. Anyone making such unauthorized modifications is responsible for the consequences. - The information in this manual is provided on the basis of information that was available at the time the manual was
written. Settings, procedures, part numbers, software and other items can change. These changes can affect the
maintenance performed on the machine. Ensure that you have complete and current information from your dealer
before you start any machine operation. - DO NOT OPERATE or permit anyone to operate or service this machine until you or the other persons have read and
understand the safety, operation and maintenance instructions in this manual. Use only trained operators who have
demonstrated the ability to operate and service this machine correctly and safely. - This operator’s manual is to be stored in the manual compartment equipped on this machine. Make sure this manual
is complete and in good condition. Contact your dealer to obtain additional manuals or manuals in languages other
than that of the country of use. - Your dealer is at your disposal for any further information. He will also provide any after-sales service you may require
and genuine replacement parts, your guarantee of quality and match. - This manual contains information concerning the adjustment and maintenance of your new equipment. You have
purchased a dependable machine, but only by proper care and operation can you expect to receive the performance
and long service built into this equipment. Please have all operators read this manual carefully and keep it available
for ready reference. - Your authorized dealer will instruct you in the general operation of your new equipment. Your dealer’s staff of factory-
trained service technicians will be glad to answer any questions that may arise regarding the operation of your
machine.
TABLE OF CONTENTS:
Case 1021G 1121G Stage IV Wheel Loader Operator’s Manual 51576098 – PDF DOWNLOAD
1 GENERAL INFORMATION
Note to the Owner 1-1
Intended use 1-4
Electro-Magnetic Compatibility (EMC) 1-5
Manual scope and required training level 1-6
Metric and imperial units abbreviations 1-8
Product Identification 1-11
Operator’s Manual storage on the machine 1-14
Machine orientation 1-15
Identification of machine components 1-16
EC Declaration of Conformity 1-18
2 SAFETY INFORMATION
Safety rules and signal word definitions 2-1
Personal safety 2-2
Safety rules 2-3
Seat belts 2-11
Support strut and service link 2-12
Utility safety 2-14
Ecology and the environment 2-15
Hand signals 2-16
Noise emission 2-22
Vibration levels 2-24
Safety signs 2-25
3 CONTROLS AND INSTRUMENTS
Access to operator’s platform
Proper entry and exit 3-1
Operator’s seat
Overview 3-3
Forward controls
Front console 3-12
Steering column 3-13
Pedal controls 3-15
Joystick steering 3-17
Right-hand side controls
Overview 3-20
Multifunction keypad 3-24
Control lever operation 3-27
Parking brake 3-35
Arm pad 3-36
Exterior controls
Hood and master disconnect 3-37
Display
Display description 3-42
Status and warning icons 3-72
Climate controls
Climate controls 3-83
Cab air louvers 3-85
Windows
Windows 3-86
Internal cab lights
Cab lights 3-88
Follow Me Home Lights 3-89
4 OPERATING INSTRUCTIONS
Commissioning the unit
Before starting the engine 4-1
Starting the unit
Starting the engine 4-2
Operating in hot temperatures 4-4
Cold temperature operation 4-5
Operating the machine 4-7
Stopping the unit
Stopping the machine 4-9
Moving the unit
Enabling the Auxiliary F-N-R switch 4-11
Ride control 4-12
Control levers 4-13
Auxiliary Forward, Neutral, Reverse (F-N-R) switch 4-21
Automatic mode 4-24
Loader functions 4-25
5 TRANSPORT OPERATIONS
Road transport
Safety rules 5-1
Recovery transport
Transporting the machine 5-2
Traveling on public roads 5-5
Moving a disabled machine 5-11
6 WORKING OPERATIONS
Loader operations
Operating tips 6-1
Joystick steering operation 6-4
7 MAINTENANCE
General information
Servicing 7-1
Releasing pressure in the hydraulic system 7-3
General specification – Diesel fuel 7-5
Biodiesel 7-6
Fluids and lubricants 7-8
Engine cooling system 7-16
Automatic lubrication system 7-18
Selective Catalytic Reduction (SCR) – Overview 7-23
Selective Catalytic Reduction (SCR) system 7-30
Maintenance planning
Maintenance chart 7-45
Daily inspection
Daily inspection 7-47
Every 10 hours
Engine oil level – Check 7-51
Every 50 hours
Bucket/attachment fittings – Grease 7-52
Machine fittings – Grease 7-53
Hydraulic oil level – Check 7-55
Transmission oil level – Check 7-56
Engine coolant level – Check 7-58
Initial 100 hours
Wheel nuts tightening – Check 7-59
Axle cooler filters (if equipped) – Replace 7-60
Selective Catalytic Reduction (SCR) in-line supply filter – Clean 7-62
Engine oil (Initial) – Change 7-64
Engine oil filter (Initial) – Replace 7-66
Fuel pre-filter (Initial) – Replace 7-67
Fuel filter (Initial) – Replace 7-68
Hydraulic oil filter (Initial) – Replace 7-70
Front and rear axle oil (Initial) – Change 7-73
Every 100 hours
Machine fittings – Grease 7-76
Every 250 hours
Drive shaft slip joints – Grease 7-79
Cab air recirculation filter – Cleaning 7-80
Cab air pre-filter – Cleaning 7-82
Cab air filter – Cleaning 7-84
Wheels – Tire inflating 7-86
Drive belt – Check 7-88
Every 500 hours
Engine oil – Change 7-90
Engine oil filter – Replace 7-92
Fuel pre-filter – Replace 7-93
Fuel filter – Replace 7-94
Fuel tank sediment – Drain 7-96
Front and rear axle oil level – Check 7-97
Front and rear axle oil – Severe duty – Change 7-98
Roll Over Protective Structure (ROPS) – Check 7-101
Battery fluid level – Check 7-104
DEF/AdBlue® tank vent filter – Replace 7-105
Selective Catalytic Reduction (SCR) in-line filter – Clean 7-107
Every 1000 hours
Pivot points – Grease 7-109
Drive belt – Replace 7-111
Cab air recirculation filter – Replace 7-113
Cab air pre-filter – Replace 7-114
Cab air filter – Replace 7-115
Engine breather filter – Replace 7-117
Front and rear axle oil – Change 7-119
Every 1500 hours
Transmission oil – Change 7-122
Transmission oil filter – Replace 7-124
Transmission breather – Cleaning 7-126
Every 2000 hours
Hydraulic oil – Change 7-127
Hydraulic oil filter – Replace 7-129
Biodegradable hydraulic oil (if used) – Change 7-132
Hydraulic systems – Check 7-133
Primary engine air filter – Replace 7-134
Secondary engine air filter – Replace 7-137
Frame and cab – Lubricate 7-140
Engine valve clearance – Check and adjust 7-141
Every 4000 hours
Selective Catalytic Reduction System (SCR) supply module filter – Replace 7-142
Diesel Exhaust Fluid (DEF)/AdBlue® tank suction – Cleaning 7-145
Engine coolant – Change 7-148
As required
Fuel pre-filter – Drain fluid 7-150
DEF/AdBlue® tank neck filter – Cleaning 7-151
Urea Quality Sensor (UQS) – Replace 7-154
Air conditioning condenser – Cleaning 7-155
Parking brake – Check 7-156
Secondary steering – Check 7-158
Cab service – Check 7-160
Windshield washer fluid level – Check 7-163
Cooling box components- Check and clean 7-164
ELECTRICAL SYSTEM
Battery – Cleaning 7-165
Battery electrolyte level – Check 7-168
Auxiliary battery connections – Check 7-169
Battery – Replace 7-172
Fuses and relays – Replace 7-173
Lights – Replace 7-178
Storage
Preparation 7-183
Every 30 days 7-185
Removal 7-186
8 SPECIFICATIONS
General specification 8-1
Machine specifications and dimensions 8-7
Weight adjustments 8-18
Torque charts 8-20
Material weights 8-22
9 ACCESSORIES
General accessories 9-1
Special buckets 9-6
Medium material buckets 9-10
Telematics 9-18
VIDEO PREVIEW OF THE MANUAL:
PLEASE NOTE:
- This is the same manual used by the dealers to diagnose and troubleshoot your vehicle
- You will be directed to the download page as soon as the purchase is completed. The whole payment and downloading process will take anywhere between 2-5 minutes
- Need any other service / repair / parts manual, please feel free to contact [email protected] . We still have 50,000 manuals unlisted
S.V